Description
PropGlide 1200ml Large Kit – Foul Release Propeller Coating
Product Overview
PropGlide is a foul-release coating that when applied to your propeller(s) and running gear will increase fuel efficiency and the performance of any vessel. This super slick coating keeps your propellers clean from marine growth for extended periods of time. Gain the advantages by applying PropGlide to your vessel. This PropGlide 1200ml Large Kit will cover Propellers (36”- 48” with 5-6 blades) + Shaft, Strut, Rudder & Trim-tab
Increase in Prop Speed Means a Faster Vessel
PropGlide dramatically reduces drag on the propeller and running gear caused by even the smallest fouling. Since growth is unable to attach to PropGlide you will achieve higher RPM and vessel speed.
Improved Fuel Efficiency
Clean props and running gear provide more efficiencies to the engine and less fuel is burned and money saved!
Biocide-Free and Environmentally Friendly
PropGlide is not a prop antifoulant, it is a foul release coating. It contains no harmful biocides, and performs because it is a super slick coating!
Ease of Application
PropGlide is easy to apply for Do-It-Yourselfer’s and not just for the professional applicator.
The PropGlide 1200ml Large Kit contains:
- 2- 300ML Primer Base
- 2- 75ML Primer Hardener
- 2- 250ML Clear Topcoat
A. Preparation of the Surface
The preparation of the surfaces to be coated with PropGlide is the key for the product to work effectively.
1. Remove previous coatings, fouling organisms/marine growth from metal surfaces. All substrates that are to be coated with PropGlide must be bare metal. These areas should be machine sanded with a Dual Action sander fitted with a soft pad and 60-80 grit abrasive discs sandpaper. Use 60 – 80 grit wet/dry sandpaper, with water as a lubricant. Make sure the sand paper is changed frequently to ensure the necessary profile is achieved.
2. Once the surface sanding process is completed, wash all the areas with clean fresh water and wipe with clean, lintfree cotton rags soaked in water to wipe off sanding residue.
3. After cleansing with water is completed, use a rag soaked in acetone or denatured alcohol to remove water on the sanded surface.
Continue to use the rag until it becomes dry from evaporation of the acetone or denatured alcohol.
B. Apply the Etching Primer
There is a Primer Base (Part 1) and a Primer Hardener (Part 2) to activate the primer base. This two-component etching primer dries chemically by reaction of the mixed components and provides protection against corrosion and increases the adhesive property of the subsequent coats. It may be used as a pre-treatment primer on non-ferrous metals such as bronze and aluminum as well as zinc and galvanised iron. May also be used as pre-treatment primer on blast-cleaned steel plates.
PropGlide Etching Primer Physical Properties
Mixing Ratio: Primer Base (Part 1) : Primer Hardener (Part 2) = 4 : 1 by volume
Colour: Primer Base (Part 1) : Yellow, Primer Hardener (Part 2) : Clear
Dry Film Thickness: 8 microns
Drying Time: 5-15 minutes touch dry (temperature dependent)- 1 hour hard dry @ 20°C/68°F
Painting Interval: Apply PropGlide Clear TopCoat when Etching Primer is just touch dry Pot Life: 8 hrs @ 20°C/68°F
1. Agitate the Primer Base (Part 1) contents by scraping the bottom and sides of the can, as there will be settling. Mix contents of primer until the settled parts are incorporated back into solution and uniformly blended. Do not strain material, even if particles are present.
2. Stir Primer Hardener (Part 2) then add entire contents to the Primer Base (Part 1) container. Mix primer base and hardener for 30 seconds and apply mixture to sanded surface immediately after mixing.
3. Application of the Primer Base/Hardener mixture should be thin. The method of application of the primer may be done by using either a natural bristle brush or foam roller.
4. Apply a second coat of Primer Base/Hardener mixture after the first coat dries.
C. Apply the Clear Top Coat
The Clear Top Coat that should be applied to the last coat of Etching Primer within 5-15 minutes. The Clear Top Coat serves as a slick finish that will inhibit marine growth from attaching to the surface.
PropGlide Clear Top Coat Physical Properties:
Binder type: Silicone Polymer
Solvent: Xylene
Colour: Clear coating
Finish: Glossy
Dry time: 45 minutes touch dry ; 8 hours hard dry @ 20°C
Recommended film build: 75 microns per coat
Thinning: N/A
Clean up: Acetone
Shelf life: 12 months
1. After 5 to 15 minutes (depending on temperature) of applying the 2nd coat of Primer/Hardener mixture promptly apply the Top Coat. Application of Top Coat should be thicker than Primer/Hardener mixture, yet not thick enough so that the Top Coat produces runs. The Top Coat is to be applied with brush only, NO foam applicators are to be used.
2. Let the Top Coat dry overnight before launching.